服务咨询电话:18128116842

汽车清洗设备
您当前的位置 : 首 页 > 产品中心 > 润滑机系列

ZC-920Q润滑系统清洗专用设备

产品属性

  • 所属分类:润滑机系列
  • 产品编号:1570851929
  • 浏览次数:0
  • 发布日期:2019-10-21
  • 产品概述
  • 性能特点
  • 技术参数

C-920Q润滑系统清洗专用设备

清 洗 系 统 的 特 性 和 功 能

1.压力表:显示在清洗过程中发动机怠速运转时的油压大小。

2.视窗:显示清洗过过程中旧油颜色,

3.排旧油清洗阀:将此开关箭头指向“开”时,压缩空气可将留在发动机中的全部残留清洗剂混合液吹出汽车的润滑油道。当指向“关”时,停止工作。

4.清洗液加注开关:将开关箭头指向“开”时,将储液瓶里的清洗剂加入

5.汽车润滑油道里。当指向“关”时停止工作。

6.压缩空气接口:连接汽源。

7.回油管:使用合适的连接头,连接到滤清器的连接口(边上10mm)。

8.出油管:使用合适的连接头,将该管线接到有颜色标记的螺旋滤清器接到中心接口(12mm)上。

9.滤芯:每台车更换一个。

10.清洗液储液瓶:储存清洗液。

(1)压力表

(2)视窗

(3)清洗液加液口

(4)电源开关

(5)转向阀

(6)进油管

(7)回油管

清 洗 发 动 机 润 滑 系 统

概述:动态方式清洗发动机就是发动机在怠速运转情况下(或稍高于怠速运转)清洗发动机润滑系统。这种方法是最有效,最彻底的清洗发动机整个润滑系统的方法,包括清洗油压挺杆、阀门、齿轮系、机油泵、阀门盖、曲柄箱体,机油底盘和发动机内部任何一个与机油接触的层面。但是,这种方法只能在发动机性能良好的情况下使用。当发动机老化,出现烧机油,缸压降低的情况时,就应该使用静态方式清洗发动机的润滑系统。也就是在发动机停机状态下清洗发动机。

每清洗1台车更换一个滤芯。

在清洗前,发动机必须预热到正常工作温度。在清洗过程中不需要一个附加的加热器。发动机本身就可以提供清洗过程所需要的热量。

清洗发动机的时间为5-10分钟,一些发动机包括柴油发动机在清洗润滑油系统时时间要长一些。

在清洗过程中发动机的机油流过清洗机的滤清器,清洗液和发动机中的机油混合。发动机中的机油即可润滑发动机又可将清洗液带入发动机的各个润滑部位。每分钟该混合液流过发动机和清洗机滤清器2到3次(汽油发动机)。清洗液在此过程中就可以将润滑系统中的积碳、积胶、金属粉末等杂质清洗出来。像金属粉末等重物被冲进机油底盘,然后在发动机油泵的作用下被带入清洗机中的滤芯后,被过滤出来。清洗结束后,将机油放出。清洗机的压缩空气可将发动机中所剩余的油液排出。排出旧机油,换上新机油。

步骤一:要确保发动机中机油量不能低于测油杆上的zui低标记。在清洗机的储油箱倒入清洗液。在清洗机的滤清器中安装一个干净的滤芯。

步骤二:从发动机上卸下机油滤清器,换上合适的滤清器接头。

注意:接头很容易拧上。不要用强力,用手拧紧即可。

    将出油油管连接到滤清器接头的中心口,回油管连接到滤清器接头的边口。注意:中心口螺纹对出油管接头端口是12MM。边口螺纹对回油接头端口是10MM。

此时清洗机的全部开关都是关闭位置,将压缩空气管线连接到清洗机侧面标有压缩空气入口的接口上。

步骤三:将清洗剂加注开关箭头指向“开”,压缩空气将清洗剂输入到发动机里大约(15到20秒)。当加完清洗剂后,将清洗剂加注开关箭头指向“关”。启动发动机,使发动机怠速运转。检查有无渗漏现象,然后通过压力表观察油压。

步骤四:当清洗到5-10分钟后,将发动机关闭。拆开油底壳放油螺丝。将旧机油和清洗液排出。当旧机油流速很慢时,将气清洗开关箭头指向“开”。此时大约用1分钟时间可将发动机内剩余油液排出。然后将气清洗开关箭头向“关”,拧上放油螺丝。卸下滤清器接头,装上新滤清器。换入合适的机油。启动发动机,检查有无渗漏现象。最后检查一个机油液面位置。

清洗系统的维护和保养

 清洗系统从设计上保证了该设备使用多年不用维修。

要定期检查机器各连接点是否松动,各个管线连接是否紧固。及时更换损害部件和管线。

不能用太大的力量拆卸和安装滤清器接头。用手拧紧即可。

LIDA润滑系统接头明细表(0-11)   珠海市志诚汽车保养设备科技有限公司


接头图片

适合车型

接头图片

适合车型

接头图片

适合车型

0

大部分车系,通用接头,标配接头

4

大部分车系,通用接头,标配接头

8

德,日,及大部分车系,标配接头

1

大部分车系,通用接头 ,标配接头


5

大部分车系,通用接头,标配接头

9

美系,标配接头

2

大部分车系,通用接头 ,标配接头

6

大部分车系,通用接头 , 标配接头

10

所有车系,标配接头

3

大部分车系,通用接头 ,标配接头

7

日系,韩系,标配接头

11

所有车系,标配接头


Cleaning system features and functions




1. Pressure Gauge: Shows the amount of oil pressure during idling of the engine during cleaning.


2. Window: shows the old oil color during cleaning,


3. Older Oil Purge Valve: With this switch arrow pointed "on", compressed air will blow all of the remaining detergent mixture remaining in the engine out of the vehicle's lube gallery. When pointing to "off", stop working.


4. Cleaning fluid filling switch: When the switch arrow points to "open", add the detergent in the storage bottle


Car lubrication Road. Stop working when it points to "Off".


6. Compressed air interface: connect the steam source.


7. Return line: Connect to filter connection (10mm edge) using a suitable connector.


8. Outlet tubing: Connect the tubing to a color-coded spiral filter to the center port (12mm) using a suitable connector.


9. Filter: one for each car.


10. Cleaning liquid storage bottle: storage of cleaning fluid.






(1) pressure gauge


(2) window


(3) cleaning solution plus liquid mouth


(4) power switch


(5) steering valve


(6) into the pipe


(7) Return pipe








            Clean the engine lubrication system




Overview: The dynamic way to clean the engine is to clean the engine's lubrication system with the engine idling (or slightly above idling). This method is the most efficient and thorough method of cleaning the entire engine lubrication system, including cleaning the hydraulic tappet, valves, gear trains, oil pump, valve cover, crankcase, oil pan and any internal engine contact with the oil Level. However, this method can only be used with good engine performance. When the engine is aged, there is burning oil, cylinder pressure decreases, you should use a static way to clean the engine's lubrication system. That is, the engine is shut down when the engine is shut down.


Each cleaning a car to replace a filter.


Before cleaning, the engine must be warmed to normal operating temperature. There is no need for an additional heater during the cleaning process. The engine itself can provide the heat needed for the cleaning process.


The time to clean the engine is 5-10 minutes, and some engines, including diesel engines, take longer to clean the lube system.


In the cleaning process, the engine oil flows through the filter cleaner, cleaning fluid and engine oil mixture. The engine oil can lubricate the engine but also the cleaning fluid into the engine lubrication parts. The mixture flows through the engine and washer filters for two to three times per minute (petrol engine). In this process, the cleaning liquid can deposit carbon deposits, plastic deposits, metal powder and other impurities in the lubrication system


Wash it out Heavy objects such as metal powder are forced into the oil pan and then filtered into the filter cartridge in the washer by the engine oil pump. After cleaning, release the oil. The compressed air from the washer discharges the remaining oil in the engine. Discharge the old oil, put on the new oil.




Step one: Make sure that the engine oil quantity can not be lower than the lowest mark on the dipstick. In the washing machine


Pour the reservoir into the cleaning solution. Install a clean filter in the cleaner's filter.


Step 2: Remove the oil filter from the engine and change to the appropriate filter connector.


Note: The connector is easily screwed on. Do not use strong, tighten it by hand.


    Connect the outlet tubing to the center of the filter fitting and the return tubing to the lip of the filter fitting. Note: The center of the thread on the outlet connector is 12MM. Edge thread to the oil return connector port is 10MM.


At this point all the switches of the washing machine are closed and the compressed air line is connected to the port labeled compressed air inlet on the side of the washer.


Step three: the cleaning agent filling switch arrow point to "open", compressed air will detergent input to start


Machine about (15 to 20 seconds). When finished cleaning agent, the cleaning agent filling switch arrow point "off." Start the engine


Let the engine idle speed. Check for leaks and observe the oil pressure through a pressure gauge.


Step 4: When cleaning to 5-10 minutes, the engine off. Open the oil pan drain screw. Discharge old oil and cleaning fluid. When the old oil flow is slow, point the purge switch arrow to "On." About 1 minute at this time can be the remaining oil within the engine discharge. Then turn the gas purge switch arrow to "OFF" and screw in the drain screw. Remove the filter fitting and install the new filter. Change into suitable oil. Start the engine and check for leaks. Finally check the level of one oil level.






Cleaning system maintenance and care




    Cleaning system from the design to ensure that the device is used for many years without maintenance.


    To regularly check the machine connection points are loose, the connection of each pipeline is tight. Timely replacement of damaged parts and pipelines.


Do not use too much force to disassemble and install the filter connector. Tighten it by hand.








 LIDA Lubrication System Joint Schedule (0-11) Zhuhai Zhicheng Automobile Maintenance Equipment Technology Co., Ltd.


Connector picture


Suitable for the car


Connector picture


Suitable for the car


Connector picture


Suitable for the car


0


Most cars, universal joints, standard fittings


4


Most cars, universal joints, standard fittings


8


Germany, Japan, and most cars, standard fittings


1


Most cars, universal joints, standard fittings




5


Most cars, universal joints, standard fittings


9


American Department, standard fittings


2


Most cars, universal joints, standard fittings


6


Most cars, universal joints, standard fittings


10


All cars, standard fittings


3


Most cars, universal joints, standard fittings


7


Japanese, Korean, standard fittings


11


All cars, standard fittings


标签

上一篇:没有了

最近浏览:

联系我们:

电话:0760-86637060

手机:18128116842

传真:0760-86637050

邮箱:551660872@qq.com

网址:www.zc-qb.com

地址:中山市坦洲镇振兴北路1号

底部导航:

产品中心                成功案例

关于我们                新闻中心

招商加盟                联系我们

二维码:
Copyright © 珠海市志诚汽车保养设备科技有限公司 All rights reserved 备案号:粤ICP备14002069号-1 专业从事于汽车养护设备,汽车保养设备,汽车清洗设备, 欢迎来电咨询! 技术支持:祥云平台 服务支持:澳捷信息